This guide covers what changes when a trailer-mounted turbine runs in cold climates, whether it is bridging a data center campus until the grid connection arrives or supporting an industrial site through a seasonal peak. It sets out the main risks, the equipment and procedures that address them, and a readiness checklist to work through before temperatures drop.
Cold air helps output, up to a point
Gas turbine output rises as ambient temperature falls, because colder air is denser and the compressor moves more mass through the machine. On a mobile unit, that extra capability is often limited by something else: the generator rating, the step-up transformer, the cable or a control limit set by the manufacturer. Knowing which limit applies stops planners from counting on output the site cannot actually deliver.
The opposite view from summer, covered on our hot-ambient derate page, is useful here. A site that will run through both seasons needs a capability curve across the full temperature range, with the binding limit marked at each point. That curve, not the nameplate, should drive how many units a campus bridge plan relies on.
Inlet icing and anti-icing
Ice can form in the air inlet even when the ambient temperature is a few degrees above freezing. The air accelerates and cools as it enters the bellmouth, and in humid conditions moisture freezes onto filters, struts and the compressor inlet. Pieces breaking loose can damage compressor blades, and ice on filters raises pressure drop until the unit trips or derates.
Anti-icing systems warm the incoming air, typically by recirculating compressor bleed air or using heat from the exhaust or an external heater. They should switch on automatically from temperature and humidity sensors, with alarms on high filter differential pressure. Coalescer and weather hood arrangements matter as much as heating; the field guide to inlet filters explains how those stages are maintained.
Fuel gas: regulator cooling and hydrates
When natural gas drops in pressure across a regulator, it cools, often by several degrees for every large pressure step. In winter, a regulator that was fine in summer can deliver gas cold enough to freeze moisture on the outside of the valve or, if the gas carries water vapour, to form hydrates inside the pipe. Either can choke fuel flow at the worst moment.
Line heaters upstream of pressure reduction, heat tracing and insulation on exposed sections, and confirmation that delivered gas meets the dew point in the turbine fuel specification are the usual defences. Fuel gas condition is covered more widely in our fuel quality field notes.
Liquid fuel in freezing conditions
Many mobile turbines can run on distillate as a backup or primary fuel. Diesel thickens and forms wax crystals as it approaches its cloud point, which can block filters and starve the fuel system. Winter grade fuel suited to local lows should be specified for the storage on site, with suppliers asked for the cloud point and cold filter plugging point on each delivery.
Tank heating, insulated and traced fuel lines, and enclosed filter housings reduce risk further. Fuel that sat in tanks from the warmer months should be checked before the first cold snap rather than discovered during a start attempt.
Lube oil, enclosures and starting
Cold lube oil is viscous and can delay a start or trigger low pressure trips. Tank heaters and enclosure heaters keep oil and auxiliary equipment above a minimum temperature while the unit is on standby. The heater circuits need a reliable auxiliary supply, which on a remote site often means a small diesel set or a protected feed from the grid, and their failure should raise an alarm.
Starting systems suffer too. Batteries lose capacity in the cold, hydraulic starters need warm fluid and electric starters draw more current on stiff machines. Battery heaters or warm enclosures, and a test start on a cold morning before the season, give confidence. Oil grade selection is discussed in the lube oil field guide.
Snow, frozen ground and site layout
Snow drifts against inlet filter houses, blocks enclosure doors and buries cable runs and fuel connections. Layout should allow plough access around each trailer, keep inlets clear of drifting snow from prevailing winds and avoid placing air intakes where exhaust plumes can recirculate warm, moist air into them.
Ground conditions change too. Frost heave can lift pads and push trailers out of level, and spring thaw can soften gravel areas so heavy vehicles sink. Inspect levelling and supports through the season. Flexible power cables become stiff in the cold, so avoid moving or re-terminating them in deep frost unless they are rated for it.
Crew safety and a winter checklist
Operators working at night in freezing conditions face slips, frostbite and fatigue. Heated welfare cabins, lit walkways, gritting and rotation of outdoor tasks are basic but often forgotten until conditions arrive. Emergency response plans should assume roads may be closed and response times longer than in summer.
Before the season, work through a short checklist: anti-icing tested, heaters and tracing proven with alarms, winter fuel on site, batteries load tested, a cold start demonstrated, snow clearance arranged and spares for heaters and sensors stocked. For campus bridge sites, align that list with the owner’s plan described in our data center bridge power page, and with the long term O&M plan for the units.
About the authors
This guide comes from the USP&E mobile power and field operations engineering team. USP&E is an EPC and O&M contractor, not a broker, with 150+ power projects in 45+ countries, 25,000 MW contracted since 2002 and 24+ years in the field. How turbines compare with engines for this kind of duty is set out in our turbine and engine comparison.
Offices: Colorado Springs (1755 Telstar Dr, Suite 300), Knoxville (800 S Gay St, Suite 700), London (162-168 Regent Street), Johannesburg (22 Kildoon Rd, Bryanston), Cape Town (31 Brickfield Road, Woodstock) and China (No. 1 Ningzhou Road, Wuxi). Regions: USA | AFRICA | UK | UAE | CHINA. ISO 9001 and ISO 45001 certified.
Cold weather turbine questions
Do gas turbines produce more power in cold weather?
Yes, colder air is denser so output rises, but on mobile units the generator, transformer or control limits often cap the usable gain.
What is gas turbine inlet icing?
Ice forming on filters and the compressor inlet as air accelerates and cools, which can occur slightly above freezing in humid conditions.
How is inlet icing prevented?
Anti-icing systems warm the inlet air using compressor bleed air or external heat, switched on automatically by temperature and humidity sensors.
Why does fuel gas cause problems in winter?
Gas cools as pressure drops across regulators, which can freeze moisture or form hydrates. Line heaters and tracing prevent this.
What should be checked before winter on a mobile turbine site?
Anti-icing, heaters and tracing, winter grade fuel, battery condition, a cold start test, snow clearance and heater spares.
Can diesel backup fuel freeze?
Diesel forms wax near its cloud point and can block filters. Winter grade fuel, tank heating and traced lines reduce the risk.
Prepare a site for winter
Send the site location, expected winter lows and the turbine models on site, and our engineers will review the cold weather readiness plan.
Phone +27 10 822 2324 during office hours, or write to info@uspeglobal.com at any time; the field engineering contact page also routes straight to our project engineers. Mobile and packaged units are listed in our turbine inventory.
No responses yet